Red Hat RH302 ExamRed Hat Certified Engineer on Redhat Enterprise Linux 5 (Labs)

Total Question: 330 Last Updated: May 19,2017
  • Updated RH302 Dumps
  • Based on Real RH302 Exams Scenarios
  • Free RH302 pdf Demo Available
  • Check out our RH302 Dumps in a new PDF format
  • Instant RH302 download
  • Guarantee RH302 success in first attempt

Price: $110.95 $55.95

Buy Now Free Trial
PDF Version Software Version

100% Guarantee on Products High Success Rate, supported by our 99.3% pass rate history and money back guarantee should you fail your exam.

Updated regularly Get hold of Updated Exam Materials Every time. Free updates without any extra charges to the actual exam.

RH302 PDF Questions & Answers Available in a universal Adobe PDF format. Portable and printable anywhere anytime.

Quality and Value Exact Exam Questions with Correct Answers, verified by Experts with years of Experience in IT Field.

Customizable Testing Engine Simulates a real world exam environment to prepare you for RH302 Success.

Unlimited Practice RH302 Exam Re-takes Practice Until you get it right. With options to Highlight missed questions, you can analyse your mistakes and prepare for Ultimate RH302 Success.

Special Promotion More than 30% Discount for Royal Pack.

[Tested] RH302 Red Hat download 91-100 (May 2017)

Exam Code: RH302 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Red Hat Certified Engineer on Redhat Enterprise Linux 5 (Labs)
Certification Provider: Red Hat
Free Today! Guaranteed Training- Pass RH302 Exam.


You are giving RHCT Exam and in your Exam paper there is a question written, make successfully ping to

Answer and Explanation:

In Network problem thinks to check:

1. IP Configuration: use ifconfig command either IP is assigned to interface or not?

2. Default Gateway is set or not?

3. Hostname is set or not?

4. Routing problem is there?

5. Device Driver Module is loaded or not?

6. Device is activated or not?

Check In this way:

1. use ifconfig command and identify which IP is assigned or not.

2. cat /etc/sysconfig/network à What, What is written here. Actually here are these parameters.

NETWORKING=yes or no




- Correct the file

3. Use vi /etc/sysconfig/network-scirpts/ifcfg-eth0 and check the proper options







4. Use service network restart or start command


Install the Redhat Linux RHEL 4 through NFS. Where your Server is having IP and shared /var/ftp/pub. The size of the partitions are listed below:

/ à 1048

/home à 1028

/boot à 512

/var à 1028

/usr à 2048

Swap -> 1.5 of RAM Size

/data à configure the RAID Level 0 of remaining all free space.

After completing the installation through NFS solve the following questions. There are two networks and As well as there are two domains on network and on network. Your system is based on domain.

Answer and Explanation:

1. Insert the CD on CD-ROM and start the system.

2. In Boot: Prompt type linux askmethod

3. It will display the language, keyboard selection.

4. It will ask you for the installation method.

5. Select the NFS Image from the list

6. It will ask the IP Address, Net mask, Gateway and Name Server. Select Use

Dynamic IP Configuration: because DHCP Server will be configured in your exam lab.

7. It will ask for the NFS Server Name and Redhat Enterprise Linux Directory.

Specify the NFS Server:

Directory: /var/ftp/pub

8. After Connecting to the NFS Server Installation start in GUI. Go up to the partition screen by selecting the different Options.

9. Create the partition According to the Question because Size and what-what partition should you create at installation time is specified in your question

10. Create the two RAID partitions having equal size of remaining all free space.

11. Click on RAID button

12. Type mount point /data

13. Select RAID Level 0

14. Click on ok

15. Then select the MBR Options, time zone and go upto package selections.

It is another Most Important Time of installation. Due to the time limit, you should care about the installation packages. At Exam time you these packages are enough.

X-Window System

GNOME Desktop

(these two packages are generally not required)

Administration Tools.

System Tools

Windows File Server

FTP Servers

Mail Servers

Web Servers

Network Servers


Text Based Internet

Server Configuration Tools

Printing Supports

When installation will complete, your system will reboot. Jump for another Question.


Your System is going use as a router for and Enable the IP Forwarding.

i. echo "1" >/proc/sys/net/ipv4/ip_forward

ii. vi /etc/sysctl.conf


/proc is the virtual filesystem, containing the information about the running kernel. To change the parameter of running kernel in running state you should modify the /proc. From Next boot the system, kernel will take the value from /etc/sysctl.conf. If net.ipv4.ip_forward is 0, it disable the IP forwarding, if 1 then it enable the IP Forwarding.


You are working as a System Administrator at Certkiller. Your Linux Server crashed and you lost every data. But you had taken the full backup of user's home directory and other System Files on /dev/st0, how will you restore from that device?

Answer and Explanation:

1. Go to on that directory where you want to restore.

2. restore -rf /dev/st0

To restore from backup we use the restore command. Here backup will restore from /dev/st0 on current Directory.


neo user tried by:

dd if=/dev/zero of=/home/neo/somefile bs=1024 count=70

files created successfully. Again neo tried to create file having 70K using following command:

dd if=/dev/zero of=/home/neo/somefile bs=1024 count=70

But he is unable to create the file. Make the user can create the file less then 70K.

Answer and Explanation:

Very Tricky question from redhat. Actually question is giving scenario to you to implement quota to neo user. You should apply the quota to neo user on /home that neo user shouldn't occupied space more than 70K.

1. vi /etc/fstab

LABEL=/home /home ext3 defaults,usrquota 0 0 àTo enable the quota on filesystem you should mount the filesystem with usrquota for user quota and grpquota for group quota.

2. touch /home/aquota.user àCreating blank quota database file.

3. mount -o remount /home àRemounting the /home with updated mount options. You can verify that /home is mounted with usrquota options or not using mount command.

4. quotacheck -u /home àInitialization the quota on /home

5. edquota -u neo /home àQuota Policy editor

See the snapshot

1 Disk quotas for user neo (uid 500):

2 Filesystem blocks soft hard inodes soft hard

4 /dev/mapper/vo-myvol 2 30 70 1 0 0

Can you set the hard limit 70 and soft limit as you think like 30.


There are more then 400 Computers in your Office. You are appointed as a System Administrator.

But you don't have Router. So, you are going to use your One Linux Server as a Router. How will you enable IP packets forward?

Answer and Explanation:

1. /proc is the virtual filesystem, we use /proc to modify the kernel parameters at running time.

# echo "1" >/proc/sys/net/ipv4/ip_forward

2. /etc/sysctl.conf àwhen System Reboot on next time, /etc/rc.d/rc.sysinit scripts reads the file

/etc/sysctl.conf. To enable the IP forwarding on next reboot also you need to set the parameter.


Here 0 means disable, 1 means enable.


Create the group named sysusers.

Answer and Explanation:

1. groupadd sysusers

groupadd command is used to create the group and all group information is stored in /etc/group file.


Using squid block Internet to Network and allow to Network.

Answer and Explanation:

1. vi /etc/squid/squid.conf


http_port 8080

#Recommended minimum configuration:

# Near the src acl src section

acl allownet src

acl denynet src


# http_access deny all

#Under Here

http_access allow allownet

http_access deny denynet

2. service squid start

3. chkconfig squid on

squid is a proxy caching server, using squid we can share the internet, block the internet, to certain network. First we should define the port for squid, the standard port for squid is 3128. We can run squid on different port by specifying http_port portnumber.

To block or allow the Internet access to hosts, we should create the acl (Access Control List). In this file we can specify only the IP address.

Example: acl aclname src IP/Netmask

After creating acl we can block or allow the internet to specified acl.

http_access allow | deny alcname


You are giving RHCE exam. Examiner gave you the Boot related problem and told to you that make successfully boot the System. While booting system, you saw some error and stop the boot process by displaying some error messages.

Kernel Panic - not syncing: Attempted to kill init!

And no further boot process. What you will do to boot the system.

Answer and Explanation:

To understand the role of a boot loader, take a step back from Linux. When you boot your computer, the BIOS starts by detecting basic hardware, including your hard drives. Once it's done, it looks for the boot loader on the Master Boot Record of the first available disk. If you're working with an older PC, the BIOS can't find your boot loader unless it's located within the first 1,024 cylinders of the hard disk.

Newer BIOSes overcome this problem with Logical Block Addressing, which is also known as LBA mode. LBA mode reads 'logical' values for the cylinder, head, and sector, which allows the BIOS to 'see' a larger disk drive.

If you have multiple hard drives, there is one more caveat. If your drives are IDE hard drives, the /boot directory must be on a hard drive attached to the primary IDE controller. If your drives are all SCSI hard drives, the /boot directory must be located on a hard drive with SCSI ID 0 or ID 1. If you have a mix of hard drives, the /boot directory must be located on either the first IDE drive or a SCSI drive with ID 0. In other words, this is not an issue on the Red Hat exams unless the computer that you're tested on has more than two hard drives. And I believe that's less likely, as that would increase the cost of the exam.

If you are getting the Kernel panic error, it means it is boot loader related problem. Redhat Enterprise Linux uses the GRUB boot loader. You can pass the kernel parameter from the boot loader as well as you can correct the kernel parameter passing from boot loader from GRUB screen at boot time.

GRUB boot loader configuration file is: /etc/grub.conf

And Correct Configuration is:





title Red Hat Enterprise Linux ES (2.6.9-5.EL)

root (hd0,0)

kernel /vmlinuz-2.6.9-5.EL ro root=LABEL=/ rhgb quiet

initrd /initrd-2.6.9-5.EL.img

Probably miss-configured the boot loader, so giving this problem. You can pass the correct parameter from GRUB prompt:

If you know all parameters and sequence of the boot loader you can enter in command prompt also.

Press c on GRUB screen.

Grub> root (hd0,0)

grub> kernel /vmlinuz-2.6.9-5.EL ro root=LABEL=/ rhgb quiet

grub> initrd /initrd-2.6.9-5.EL.img



You are working as a System Administrator at Certkiller. Your Linux Server crashed and you lost every data. But you had taken the full backup of user's home directory and other System Files on /dev/st0, how will you restore from that device?

Answer and Explanation:

1. Go to on that directory where you want to restore.

2. restore -rf /dev/st0

To restore from backup we use the restore command. Here backup will restore from /dev/st0 on current Directory.

Related RH302 Articles

best-it-exam-    | for-our-work-    | hottst-on-sale-    | it-sale-    | tast-dumps-us-    | test-king-number-    | pass-do-it-    | just-do-it-    | pass-with-us-    | passresults-everything-    | passtutor-our-dumps-    | realtests-us-exam-    | latest-update-source-for-    | cbtnuggets-sale-exam    | experts-revised-exam    | certguide-sale-exam    | test4actual-sale-exam    | get-well-prepared-    | certkiller-sale-exam    | buy-discount-dumps    | how-to-get-prepared-for-the    | in-an-easy-way    | brain-dumps-sale    | with-pass-exam-guarantee    | accurate-study-material    | at-first-try    | 100%-successful-rate    | get-certification-easily    | material-provider-exam    | real-exam-practice    | with-pass-score-guarantee    | certification-material-provider    | for-certification-professionals    | get-your-certification-successfully    | 100%-Pass-Rate    | in-pdf-file    | practice-exam-for    | it-study-guides    | study-material-sku    | study-guide-pdf    | prep-guide-demo    | certification-material-id    | actual-tests-demo    | brain-demos-test    | best-pdf-download    | our-certification-material    | best-practice-test    | leading-provider-on    | this-course-is-about    | the-most-reliable    | high-pass-rate-of    | money-back-guarantee    | high-pass-rate-demo    | recenty-updated-key    | only-for-students-free-download    | courseware-plus-kit-for    | accurate-answers-of    | the-most-reliable-id    | provide-training-for    | welcome-to-buy    | material-for-success-pass    | provide-free-support    | best-book-for-pass    | accuracy-of-the-answers    | pass-guarantee-id    |    |    |